Products › Wafer Mounter › Manual Wafer Mounter P-200 / P-300

Manual Wafer Mounter P-200 / P-300

Prepares wafers for dicing — mounts each wafer onto a film frame with commercially available dicing tape, free of voids and air bubbles, with quick changeovers for high-mix production.

Wafer size2″ to 8″
Frame8″ (6″ with insert ring)
Weight19 kg42 lb
  • Void-free mounting of wafers 50 µm to 4.5 mm thick
  • Adjustable chuck height protects thin, brittle wafers
  • Chuck change in under 2 minutes, height included
  • Over 120 mounts per hour, minimal maintenance
  • Swiss-engineered, in production since 1996

Technical data

P-200P-300
Wafer size2″ to 8″2″ to 300 mm (12″)
Frame size, standard8″300 mm
Frame size with insert ring6″8″ or 6″
Tape width150 to 300 mm150 to 400 mm
Width460 mm18.1 in590 mm23.2 in
Depth680 mm (875 mm with PTW)26.8 in (34.4 in with PTW)880 mm (1000 mm with PTW)34.6 in (39.4 in with PTW)
Height230 mm9.1 in250 mm9.8 in
Weight19 kg (25 kg with PTW)42 lb (55 lb with PTW)25 kg (33 kg with PTW)55 lb (73 lb with PTW)
Same on both models
Wafer typeFlat surface on the mounting side (not for bumped or TAIKO wafers)
Wafer thickness50 µm to 4.5 mm (thinner or thicker on request)
Wafer materialsSi, SiC, Ge, GaAs, glass, FR4, ceramics and others
Frame typesDISCO (DTF 2-6-1, DTF 2-8-1, DTF 2-12, DTF 2-12-1) and K&S; switched with exchangeable positioning pins
TapeCommercially available standard and UV release dicing tapes
ThroughputOver 120 mounts per hour (operator dependent)
UtilitiesVacuum only. Electrical power is needed only for the PTW and ESD Neutralizing Bar options.
Vacuum−70 kPa, tube connection 6 mm OD−20.7 inHg, tube connection 6 mm OD
Power, PTW option85 to 240 VAC
Power, ESD Neutralizing Bar option110 V / 60 Hz or 230 V / 50 Hz (controller)
CleanroomIn use up to ISO 4–5
Service life and warrantyDesigned for more than 10 years; 12-month warranty from dispatch, consumables excluded (Terms & Conditions)
ConformityCE; EN 60204-1 (electrical equipment of machines)

Description

How it works

The wafer lies face down on the vacuum chuck, where carbon tissue protects the processed surface. The operator places the frame on the positioning pins, pulls tape from the reel across wafer and frame, presses it on with the pad roller, and trims it along the frame with the circular blade. The chuck height is adjustable relative to the frame table. Set correctly, most of the roller force goes into the frame table, while the pad roller and chuck absorb the rest. In practice, too little force, which leaves voids, is the more common error. Engineered in Switzerland, the P-series has been in production since POWATEC was founded in 1996.

Typical applications

Mounting before dicing in high-mix and medium-volume production; one unit can supply up to three dicing saws. Thin wafers below 100 µm and brittle materials such as GaAs, in production. Si, SiC, Ge, glass, FR4 and ceramic substrates. UV release tapes and tapes with a liner (with the Protection Tape Winder), and ESD-sensitive devices (with the ESD Neutralizing Bar). Slightly bowed or warped wafers, wafer fragments, square substrates and several substrates per cycle on the Ceramic Mounting Chuck, which holds with an even vacuum across its entire surface (non-SEMI sizes and shapes as custom chucks).

Changeover and configuration

Use one chuck per wafer size: the vacuum channel must be fully covered by the wafer. A chuck change, including height adjustment, takes under 2 minutes. For frequent changes between wafer sizes, we recommend the V-200 / V-300 Vacuum Wafer Mounter. An insert ring adds a smaller frame size in under 1 minute; exchangeable pins switch between DISCO and K&S frames. Reference lines on the reel holder keep tape changes repeatable.

Not suited for

Wafers whose processed surface must not be touched: use the P-200 NC / P-300 NC Non-Contact Wafer Mounter, or a Non-Contact Chuck on this machine. Bumped wafers or lenses: use the V-200 / V-300 Vacuum Wafer Mounter or the heated V-200H / V-300H. TAIKO wafers: use the V-200T / V-300T.

Options and accessories

Chucks

Every chuck type is available for all SEMI wafer sizes the machine handles, 2″ to 8″ on the P-200 and 2″ to 300 mm on the P-300.

Standard Mounting Chuck

Vacuum chuck with height adjustment and a Wafer Protection Set (porous sub-layer plus carbon tissue) that protects the wafer surface. Chuck change under 2 minutes.

Ceramic Mounting Chuck

Porous ceramic surface with an even vacuum across the entire substrate. Holds thin, sensitive, slightly bowed or warped wafers, wafer fragments, and several substrates at once. Flatness to 3 µm.

Heated Mounting Chuck

Heated vacuum chuck up to 80 °C (175 °F). Higher temperatures, up to 180 °C (356 °F), are possible on request.

Non-Contact Chuck

Holds the wafer by its edge exclusion zone only (up to 5 mm, depending on wafer size), so the processed surface is never touched. A pressurized cavity under the wafer balances the roller force.

Customized Chuck

Combined chuck functions, non-SEMI dimensions, non-circular shapes, alternative materials (Teflon coating, stainless steel), or ceramic with a protective surface.

Machine options

Protection Tape Winder (PTW-200 / PTW-300)

Motor-driven winder integrated in the machine. Separates and collects the liner from any tape with a backing. Draws power only while tape is pulled.

85 to 240 VAC

ESD Neutralizing Bar & Controller (ESD-200 / ESD-300)

Pre-installed at the tape peel-off point, where most static charge is generated. Limits ESD to < 100 V. Includes controller.

Controller 110 V / 60 Hz or 230 V / 50 Hz

Insert Ring

Removable anodized aluminum ring with pins and magnets that adapts the machine to a smaller frame. Conversion in under 1 minute.

P-200: 6″ (DISCO DTF 2-6-1 or K&S) · P-300: 8″ or 6″ (DISCO or K&S)

Tape Storage Box

Keeps one spare tape roll on its reel, clean and ready for a quick tape change. Sized by tape width - for tapes up to 300 mm (P-200) or 400 mm (P-300).

Wafer alignment

Wafer Centering Template

Stainless steel template based on the DISCO frame design. Uses the frame positioning pins as reference to center the wafer and set the notch at 3, 6, 9 or 12 o’clock.

P-200: 6″, 8″ · P-300: 6″, 8″, 300 mm (DTF 2-12 or DTF 2-12-1)

Precision Wafer Alignment Fixture

Aluminum fixture made to your wafer drawing. Centers the wafer and fixes the notch at 12 o’clock relative to the frame; accounts for wafer and frame thickness, so no chuck height change is needed. Wafer drawing required before ordering.

P-200: 8″ · P-300: 8″, 300 mm

Utilities

Silent Table-Top Vacuum Pump

Compact, oil-free diaphragm pump that supplies the chuck vacuum where no house vacuum is available.

Ultimate vacuum < 130 mbar abs. (well beyond the −70 kPa required); 100 to 240 VAC

Measurement Tool for ESD Bar

Checks each pin of the ESD bar. Regular checks are recommended, as a faulty bar can damage wafers.

Conversion kits

Laminator conversion (to L-200 / L-300)

Replacing the chuck and the circular cutting knife module converts the mounter into a back grinding tape laminator.

Custom solutions

Built to customer requirements. Tell us about your substrate or process.

Border-only mounting

Tapes only the outer 5 mm of the wafer, leaving the active area free of tape. Two lids align the process steps concentrically.

P-300

16-substrate chuck

Custom chuck that mounts 16 substrates in one cycle with high positioning accuracy.

P-200

Square ceramic chuck

A very thin, brittle square substrate did not lie flat, and any unevenness under the tape would crack it. The porous ceramic surface pulls the substrate flat across its whole area, so the tape goes on void-free. A Teflon finish along the chuck edge keeps the tape from sticking to the chuck, so the mounted substrate lifts off without force.

P-200

Video

POWATEC Manual Wafer Mounter P-200
Plays from YouTube when you click it.

FAQs

Can you test my samples before I buy?

Yes. We mount your samples free of charge, help you select a tape, and can dice or UV-cure them as needed. We document the run by video or live stream, or you can visit us for a demonstration.

How do I avoid putting too much force on the wafer?

Set the chuck height correctly. Most of the roller force then goes into the frame table, and the pad roller and chuck absorb the rest. Insufficient force, which leaves voids, is the more common problem.

Do I need a separate chuck for each wafer size?

Yes. The wafer must cover the chuck's entire vacuum channel, so we recommend one chuck per wafer size. A chuck change takes under 2 minutes. If you switch sizes often, we recommend the V-200 / V-300 Vacuum Wafer Mounter.

Can it mount wafers outside 50 µm to 4.5 mm?

Yes, with customization. Contact Powatec USA with your wafer specification.

Can it mount TAIKO or bumped wafers?

No. Use the V-200T / V-300T for TAIKO wafers and the V-200 / V-300 or V-200H / V-300H for bumped wafers.

Request a quote